NATA Is Australia's Leading Accreditation Organisation

This testing regime includes testing such as chemical resistance, resistance to heat ageing, water vapour transmission, water absorption and cyclic movement. Effective water external waterproofing system testing management through the strategic placement of drains and overflows is key to diverting water away from the structure efficiently. These additions act as a safeguard for the waterproofing membrane, offering robust protection against various forms of damage and environmental exposur

Our Tools: IntegriScan
The low voltage Vertical Surface Scanning roller listed under the guide for testing vertical substrates works by moistening the roller sleeve as the operator rolls the testing tool up the substrate forcing the water before it into any breaches. In areas where there are multiple breaches, further testing needs to be undertaken each time until no more breaches are identified. If there are only puddles on the surface, then the circuit would be incomplete resulting in missed breache


Electronic Leak Detection (ELD) is a external waterproofing system testing type of continuity testing, comparable to a flood test in performance. Electronic Leak Detection is a testing method applied to many waterpoofing membranes as a method of checking for the continuity of the membrane. The thickness readings are obtained by measuring the time taken for the ultrasonic signal to propagate from the probe to the coating/substrate interface and bac


This is known as the elastic or proportonal limit (also the yield strength). The percentage of elongation is calculated by the maximum external waterproofing system testing gage length divided by the original gage length. These material properties can change depending on environment, for example in extreme hot or cold conditions. This may differ from the specimen's strength when breaking depending on if it is brittle, ductile or has properties of both.
Yield Strength
For soft and porous materials, like electrospun nonwovens made of nanofibers, the specimen is usually a sample strip supported by a paper frame to favour its mounting on the machine and to avoid membrane damaging. In smaller workpieces or when critical parts of the casting must be tested, a workpiece may be sacrificed to make the test specimens. These specimens may not be exact representation of the whole workpiece because the grain structure may be different throughou

How Inspect365 Works to Give You Peace of Mind A Simple 5-Step Inspection Process
Whether prior to remedial waterproofing works being undertaken to determine scope or following completion, Waterproofing Integrity can provide confidence of issues being effectively addressed. Our team of technicians can come to your project to check on the compliance of your waterproofing installation.
About ITA
AS 4654 is the primary Australian standard that relates to the physical performance properties of waterproofing membranes specified for use… Tensile strength testing is a fundamental method for characterising the mechanical properties of waterproofing membranes, coatings, and other materials and… AS/NZS 4858 is the primary Australian standard that relates to the physical performance properties of waterproofing membranes specified for use… Wasting water along with time delays involved with flood testing in areas that are large and deep (as walls can leak as much as floors, joints and penetrations under hydrostatic pressure) external waterproofing system testing is no longer viable nor acceptable. Electronic Leak Detection [ELD testing] is fast becoming the preferred testing method for builders, waterproof manufacturers and waterproofing contractors who understand time is money on a building sit


Membranes that are designed to be fully bonded to their will exhibit reduced performance where a sufficient bond is not present. Adhesion testing is a destructive test most commonly applied on exposed areas such as rooftops and podiums. Waterproofing Integrity inspectors are educated in what is required and can assess compliance with prescribed falls, terminations and detailing. Waterproofing Integrity utilise a number of types of electronic leak detection with a view to being fit for purpose and benefits that each offers. ELD creates an electric circuit through a non-conductive membrane to find coating film discontinuities that are not readily visibl


To ensure the long-term performance of any membrane system, it is critical that it is allowed to properly cure before the installation of any overburden finishes or being placed into service. The inherent properties of a membrane play a crucial role in determining its overall effectiveness and suitability for use for the proposed application. By ensuring that your building has adequate waterproofing, you can help to protect your property and ensure that it remains safe and healthy for all occupants. It is important to take proactive measures to ensure that your building remains in good condition and to prevent any water-related damage from occurrin


Selecting the right waterproofing membrane is crucial for protecting your building against water damage and ensuring external waterproofing system testing the safety and well-being of its occupants. It is essential to prevent waterproofing failures by testing waterproofing membranes as a system. To maximise the durability and effectiveness of external waterproofing systems, incorporating protective measures and finishes is essential. The correct termination of waterproofing membranes is crucial for the overall effectiveness of the waterproofing system. The success of any external waterproofing system begins with meticulous substrate preparation and ensuring compatibility between the substrate and the waterproofing materials. These standards are designed to guide contractors, builders, and engineers in the selection of materials and the installation of waterproofing systems for external above-ground use, such as balconies, decks, and roofs.
Addressing Penetrations and Vulnerabilities in Waterproofing Syste